← All guides
Commercial safe guide

Steel thickness for business safes.

Gauge and plate numbers tell you what a safe is made of. They don't tell your insurer or inspector how it performs. Here's how to read the specs, and when to stop comparing steel and ask for a rating.

Reading the numbers

Gauge runs backward.

A higher gauge number means thinner steel. A 10-gauge body is thicker than a 12-gauge body, and 7-gauge is thicker than both. Sheet steel gauges follow the Manufacturers' Standard Gauge:

Gauge Inches Millimeters
7 gauge 0.1793" 4.55 mm
8 gauge 0.1644" 4.18 mm
10 gauge 0.1345" 3.42 mm
11 gauge 0.1196" 3.04 mm
12 gauge 0.1046" 2.66 mm
14 gauge 0.0747" 1.90 mm
16 gauge 0.0598" 1.52 mm

The steps are smaller than spec sheets make them sound. Going from 12-gauge to 10-gauge adds about 0.03", less than a thirty-second of an inch. Real, but only one part of how the safe performs.

Commercial construction

Sheet steel vs. plate steel.

As steel gets thicker, the industry stops using gauge and switches to fractional inches. That shift happens gradually, around 3/16" (0.1875"), and is clear by 1/4". It's why many commercial safes list a 1/2" body or a 1" door instead of a gauge.

Sheet steel bodies

Common on pharmacy cabinets and storage safes. Our 2101-17 pharmacy safe, for example, uses an 11-gauge body. Good for organized, locked daily storage.

Plate steel

Construction-rated safes are defined by plate. A C-rate is commonly a 1/2" body with a 1" door. Plate resists bending and prying far better than sheet.

Composite

High-security TL safes layer steel plates around a poured fill, often concrete with steel and abrasive aggregate. Composite always includes steel.

Why you can't compare

High-security makers don't publish their steel.

Shop TL-rated safes and you'll notice the spec sheets list overall wall and door thickness, but not the exact steel inside the composite. That's deliberate, for two reasons:

  • The recipe is the product. The blend of steel, concrete, and abrasives between the plates is proprietary.
  • Attackers read spec sheets too. Publishing exact steel would help someone plan how much cutting a breach takes.

Instead, these manufacturers let the UL rating speak for the whole design. For a TL safe, the rating is the spec that matters. See our burglary ratings guide.

Beyond thickness

What else decides how a safe holds up.

Burglars don't attack the thickest part of a safe. They look for leverage and weak points, so the whole design matters:

  • Locking bolts: the number and diameter of solid bolts holding the door to the frame.
  • Hardplate: case-hardened steel in front of the lock to slow drilling.
  • Relockers: devices that lock the bolts permanently if the lock is attacked.
  • Door fit: tight tolerances leave no gap for a pry bar.

What weight tells you

Between two safes of similar size, the heavier one is usually more solidly built. Composite fill adds a lot of weight, and it also adds fire protection and resistance to cutting tools. Weight matters for another reason in a business: a UL TL-rated safe must weigh at least 750 pounds or be anchored, so plan for your floor, your doorways, and your delivery access before you order. See delivery.

Before you buy

A checklist for comparing commercial safes.

  • Rating first: the UL burglary rating your insurer, regulator, or security policy names.
  • Body and door: gauge or plate thickness, or composite construction.
  • Lock: the UL listing (Group 2, 1, or 1R, or Type 1 electronic) and features such as an audit trail or time delay.
  • Lock protection: a hardplate in front and a relocker behind.
  • Anchoring: pre-drilled anchor holes and hardware for your floor.
  • Fire: a fire class and duration that match what you store. See our fire ratings guide.
  • Site fit: weight, dimensions, and how it gets from the truck to its final spot.